Loohan Forums
Anyone can read; just hit the Index tab. Permission is required to post. No agents need apply.
Posts in the wrong category will be relocated.
New registrants: if you try to register you will get a message that we are not accepting new members. Due to the limitations of this forum software which is not designed to deal with incessant CIA harrassment, we have no alternative but to disable automatic registration, and then we can't change this automatic message. Your account needs to be created by admin before you can post in the forums. Because otherwise, almost all registrants are CIA sock puppets. To get a forum account you need to send a brief presentation email to loohanforum at gee mail dot com, also suggesting a user name. Then we can enable you manually. But before you even do that, take a look around the forum and my site and decide whether you REALLY WANT to join/post, before you jack us around. Most seemingly genuine people who apply fail to even ever log in once to change their password after we go through the work of creating a membership for them. Then we must quickly delete their account again lest the CIA has intercepted their temporary password. And of the few who do change their password, most still never post. Maybe they realize we are too weird for them, I don't know. They get real quiet, never to be heard from again.
GLOSSARY: Sometimes unusual terminology or abbreviations are used that with some luck you might find defined here.
You are not logged in.
- Topics: Active | Unanswered
Pages: 1
#1 2016-04-14 16:15:29
- Loohan
- Administrator
- Registered: 2014-10-31
- Posts: 32,901
pyramid of April 2016
Been puttering around making a few things.
The pipes are PVC filled with resin.
I used screws to hold the diagonals into the corners:
If i do this again i'll use thicker screws and embed them more deeply, although this seems adequate.
[Edit: All 3 images on this thread completely disappeared from my hard drive and backups! I even have a site backup taken 2 months after these posts; nothing.
I think what happened is i lost some files in a backup, then used the backup to restore my site on a new host and new HD.]
Offline
#2 2016-04-15 15:21:59
- UrosS
- Enabled users
- Registered: 2016-03-08
- Posts: 121
Re: pyramid of April 2016
Hot head and hands, strong!
Offline
#3 2016-04-15 15:33:30
- Loohan
- Administrator
- Registered: 2014-10-31
- Posts: 32,901
Re: pyramid of April 2016
Yes, the 2 units work together.
Offline
#4 2016-04-16 18:20:09
- Loohan
- Administrator
- Registered: 2014-10-31
- Posts: 32,901
Re: pyramid of April 2016
I sense someone else making something like this. Vozy has been doing custom programming for their pipes.
The trickiest part was how to tie
these ends together neatly. I just used a whole $5 stick of epoxy putty and globbed the ends together. But this is very difficult, as the ends want to move all over the place, and you can't see what you're doing because there's a glob of putty covering it. So i peeked at it from underneath and tried to hold everything in as perfect a position as i could while the epoxy heated up and hardened. (The heat is not bad, but i was wearing gloves against the BPA.)
It turned out close enough, but i don't recommend trying that. Next time i will wire the ends together, maybe even drill holes for the wire, and try to lock it more or less in place. And then probably reinforce it with the putty.
To avoid excess weight, i did not pour the base until after i cast the tip in a pyramid mold. I assembled everything as is, with only the diagonals full of resin (they had to be, in order to embed the screws so that i could assemble it).
I supported the mold in the hole of a concrete block on its side, and tied 2 of the pyramid base corners onto some nearby furniture, using a level on the base. And being careful that the pipes had not partially slid out of the corner pieces. (Of course the base was upside-down and sticking in the air.)
Once the poured tip is complete, one could disassemble the base and fill the base pipes, or just leave everything together and pour resin into the ports on each corner, filling the entire base in layers.
What i did, is remove the base pipes, and in order to lock things together, stuff a folded-up, discarded disposable glove into one end of each pipe, and then fill them to an inch or so from the top, in layers.
Later i pulled out the gloves with needlenose pliers. So i had a cavity in the end of each pipe.
Then i reassembled and poured resin into the corner ports. So the epoxy should lock the pipes in strongly.
Offline
Pages: 1